ASF-Nabd/HIL_setup
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

add test

Browse Source
This commit is contained in:
mahmamdouh
2026-02-09 16:36:29 +01:00
parent af9e0c11e0
commit 0f50ddbae3
18 changed files with 610 additions and 293 deletions
Download Patch File Download Diff File Expand all files Collapse all files

2
I2C/main/CMakeLists.txt
View File

@@ -1,2 +1,2 @@
idf_component_register(SRCS "blink_example_main.c"
idf_component_register(SRCS "main.c"
INCLUDE_DIRS ".")

104
I2C/main/blink_example_main.c
View File

@@ -1,104 +0,0 @@
/* Blink Example
This example code is in the Public Domain (or CC0 licensed, at your option.)
Unless required by applicable law or agreed to in writing, this
software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "driver/gpio.h"
#include "esp_log.h"
#include "led_strip.h"
#include "sdkconfig.h"
static const char *TAG = "example";
/* Use project configuration menu (idf.py menuconfig) to choose the GPIO to blink,
or you can edit the following line and set a number here.
*/
#define BLINK_GPIO CONFIG_BLINK_GPIO
static uint8_t s_led_state = 0;
#ifdef CONFIG_BLINK_LED_STRIP
static led_strip_handle_t led_strip;
static void blink_led(void)
{
/* If the addressable LED is enabled */
if (s_led_state) {
/* Set the LED pixel using RGB from 0 (0%) to 255 (100%) for each color */
led_strip_set_pixel(led_strip, 0, 16, 16, 16);
/* Refresh the strip to send data */
led_strip_refresh(led_strip);
} else {
/* Set all LED off to clear all pixels */
led_strip_clear(led_strip);
}
}
static void configure_led(void)
{
ESP_LOGI(TAG, "Example configured to blink addressable LED!");
/* LED strip initialization with the GPIO and pixels number*/
led_strip_config_t strip_config = {
.strip_gpio_num = BLINK_GPIO,
.max_leds = 1, // at least one LED on board
};
#if CONFIG_BLINK_LED_STRIP_BACKEND_RMT
led_strip_rmt_config_t rmt_config = {
.resolution_hz = 10 * 1000 * 1000, // 10MHz
.flags.with_dma = false,
};
ESP_ERROR_CHECK(led_strip_new_rmt_device(&strip_config, &rmt_config, &led_strip));
#elif CONFIG_BLINK_LED_STRIP_BACKEND_SPI
led_strip_spi_config_t spi_config = {
.spi_bus = SPI2_HOST,
.flags.with_dma = true,
};
ESP_ERROR_CHECK(led_strip_new_spi_device(&strip_config, &spi_config, &led_strip));
#else
#error "unsupported LED strip backend"
#endif
/* Set all LED off to clear all pixels */
led_strip_clear(led_strip);
}
#elif CONFIG_BLINK_LED_GPIO
static void blink_led(void)
{
/* Set the GPIO level according to the state (LOW or HIGH)*/
gpio_set_level(BLINK_GPIO, s_led_state);
}
static void configure_led(void)
{
ESP_LOGI(TAG, "Example configured to blink GPIO LED!");
gpio_reset_pin(BLINK_GPIO);
/* Set the GPIO as a push/pull output */
gpio_set_direction(BLINK_GPIO, GPIO_MODE_OUTPUT);
}
#else
#error "unsupported LED type"
#endif
void app_main(void)
{
/* Configure the peripheral according to the LED type */
configure_led();
while (1) {
ESP_LOGI(TAG, "Turning the LED %s!", s_led_state == true ? "ON" : "OFF");
blink_led();
/* Toggle the LED state */
s_led_state = !s_led_state;
vTaskDelay(CONFIG_BLINK_PERIOD / portTICK_PERIOD_MS);
}
}

15
I2C/main/main.c
View File

@@ -5,21 +5,16 @@
void app_main(void) {
scd30_data_t sensor_data;
// Initialize the SCD30 sensor
scd30_init();
scd30_start_measurement();
// Example: SDA = 21, SCL = 22 (change as needed)
scd30_handle_t *scd30 = scd30_init(21, 22);
scd30_start_measurement(scd30);
while (1) {
// Read data from the sensor
if (scd30_read_data(&sensor_data) == 0) {
if (scd30_read_data(scd30, &sensor_data) == 0) {
printf("CO2: %.2f ppm, Temp: %.2f °C, Humidity: %.2f %%\n",
sensor_data.co2, sensor_data.temp, sensor_data.humidity);
} else {
printf("Failed to read data from SCD30 sensor\n");
}
// Wait for 2 seconds
vTaskDelay(pdMS_TO_TICKS(2000));
}
}
}